Comparison of the ASTM D Method and the film thickness method for obtaining volume solids 3. Bibliography. Buy ASTM D R TEST METHOD FOR VOLUME NONVOLATILE MATTER IN CLEAR OR PIGMENTED COATINGS from SAI Global. proper ASTM standard for determining the volatile and non- volatile content of paint D Test Method for Volume Nonvolatile Matter in. Clear or Pigmented .
|Published (Last):||3 January 2005|
|PDF File Size:||1.21 Mb|
|ePub File Size:||9.65 Mb|
|Price:||Free* [*Free Regsitration Required]|
Total suspended solids – includes all solids present in a sample that remain on a 1. The use of volume nonvolatile matter values in such instances should be carefully considered as the increased volume is largely due to air trapped in these voids.
Technical – Volume solids or solid content. Allow the excess coating material to drain off. Historical Version s – view previous versions of standard. The values given in parentheses are for information only.
Fixed solids – solids that atsm after firing a sample in a Deg C muffle furnace. Determined by evaporating a known volume of the filtrate sample in a Deg C oven.
ASTM D2697 – 03(2014)
Suspend the disc in water and weigh again. Let it be P. Let it aztm W3, grams. Determined directly by evaporating a known volume of an unfiltered water sample in a Deg C oven.
Let it be W1, grams. Suspend the coated disc in water and weigh again. Earlier collaborative studies included a gloss enamel, a flat wall paint, a gloss house enamel, an industrial baking enamel, an interior latex paint, and an exterior latex paint. This value is useful ashm comparing the coverage square feet of surface covered at a specified dry film thickness per unit volume obtainable with different coating products.
Can be performed on total, dissolved, or suspended samples to determine – total volatile solids, volatile dissolved solids, or volatile suspended solids. Take Stainless Steel Disc 60 mm diameter and 0.
Let it be W grams. Weigh the disc in air. Weigh the coated disc in air. Total dissolved solids – includes all solids present in a water sample filtered aetm a 1. Blot the coating material off the bottom edge of the disc so that beads or adtm do not dry on the bottom edge of the disc.
Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Total solids – includes all solids present in a water sample. Can be performed on total, dissolved, or suspended samples to determine – total fixed solids, fixed dissolved solids, or fixed suspended solids.
Let see how to test the TSS:. Link to Active This link will always route to the current Active version of the standard.
ASTM D – 03 Standard Test Method for Volume Nonvolatile Matter in Clear or Pigmented Coatings
Dip the disc in the paint sample for 10 minutes and take out the disc. This can be tested using IS – part Determined by filtering a known volume of sample and placing the filter and filter container in a Deg C oven for 24 hours to evaporate the water. Note the weight of the stainless-steel disc. An interlaboratory study to establish the precision of this test method included a water-reducible exterior latex paint and three automotive coatings that included a solvent-reducible primer surfacer, water reducible primer surfacer, water reducible enamel topcoat, and acrylic dispersion lacquer topcoat.
Let it be W4 grams.
[email protected]: Technical – Volume solids or solid content
I married on 30 th June having one baby Above the critical pigment volume concentration, the apparent volume of the dry film is significantly greater than theoretical due to the increase in unfilled voids between pigment particles.
Let see how may types of solids are there in liquid products or materials: One reason is that the volume occupied by a solution of resin e2697 solvent may be the same, greater, or less than the total volume of the separate ingredients: Newer Post Older Post Ast.
These test methods cover procedures for assessing the adhesion of coating films to metallic substrates by applying and removing pressure-s It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Determine the aetm gravity of the paint using mass per litre cup.